Where to spray Holts EGR Cleaner on 180 engine?

[CaliGem]

I'm aware it may only be a temp fix (see other thread), but we have some EGR Cleaner. Where on earth do we spray it on these 180 engines where the EGR valve/cooler is at the front?

 

[secret lemonade drinker]

You have to remove the egr valve and clean the internal areas loosening the tar black residue with the spray you have bought, it is a very dirty job and you will be black for weeks afterwards

 

[CaliGem]

You have to remove the egr valve and clean the internal areas loosening the tar black residue with the spray you have bought, it is a very dirty job and you will be black for weeks afterwards

Oh, I thought you just spray it into the air tube and it makes the van run rough on idle for a second each spray?

 

[WelshGas]

Oh, I thought you just spray it into the air tube and it makes the van run rough on idle for a second each spray?

AI Overview

To effectively use an EGR (Exhaust Gas Recirculation) cleaner spray, you need to apply it to the air intake manifold while the engine is running at idle. Disconnecting the air intake hose, often after the air filter, allows direct access to the intake manifold for spraying. Short bursts of spray, with engine recovery time in between, help prevent engine knocking and ensure the cleaner effectively reaches the targeted areas.

Here's a more detailed breakdown:

1. Warm up the engine: Start the engine and allow it to reach operating temperature.
   
   
2. Locate the air intake: Identify the air intake hose, typically after the air filter and before the intake manifold.
   
   
3. Disconnect the hose: Carefully disconnect the air intake hose to expose the intake manifold.
   
   
4. Start the engine (if not already running): Ensure the engine is running at idle speed.
   
   
5. Spray in short bursts: Shake the EGR cleaner can and spray short bursts (about 1 second each) into the intake manifold.
   
   
6. Monitor engine response: Observe the engine's reaction, particularly the RPM. Allow the engine to stabilize after each spray.
   
   
7. Occasional RPM increase: Briefly increase the engine RPM to 1000-1500 between sprays to help distribute the cleaner.
   
   
8. Stop if RPM drops: If the engine doesn't recover or the RPM drops significantly during spraying, stop the procedure.
   
   
9. Continue until the can is empty: Use the entire contents of the EGR cleaner can.
   
   
10. Idle and drive: Let the engine idle for 5 minutes after spraying, then drive the vehicle for a short distance (5-10 km) without exceeding 3000 RPM.
    
    
11. Final idle and shutdown: Allow the engine to idle for at least one minute before turning it off.
    
    
12. Reconnect the hose: Reattach the air intake hose.
    
    
13. Clear any codes: If the engine throws any codes, use a code reader to clear them.
    

Important notes:

• Always refer to the specific instructions on your EGR cleaner product.
  
  
• Be cautious when working around the engine, as some parts may be hot.
  
  
• Wear appropriate safety gear, such as gloves and eye protection.
  
  
• If you are unsure about any step, consult a qualified mechanic.

 

[CaliGem]

I got that far, but don't know which part to remove to spray in

 

[secret lemonade drinker]

And if it works after the spray has gone through the engine combustion process may I sell you the Eiffel tower?

 

[secret lemonade drinker]

And if it works after the spray has gone through the engine combustion process may I sell you the Eiffel tower?

Or worse you are going to dislodge all that black sludge and it is going to go through the combustion process.....if it doesn't damage the engine then why do we have air filters