T6 BIKE RACK - 7EO O71 104A

Edited as mikes link is better.

I have ordered a new style rack from Steve, the head rules the heart in terms of practicality. Also, my local dealership did their very best to avoid a sale and Steve was really good to deal with, so happy to give him my business.

Will post my first impressions next week.
 
Edited as mikes link is better.

I have ordered a new style rack from Steve, the head rules the heart in terms of practicality. Also, my local dealership did their very best to avoid a sale and Steve was really good to deal with, so happy to give him my business.

Will post my first impressions next week.
On practicality it sounds the better rack Dave. For a number of reasons I went down the tow bar rack route but if pushed I would go for the Quasimodo one.

Mike
 
I spoke to Steve in parts at SMG Cowfold today. They have two Kylie's in stock, so give him a ring if you want one.
He has some more on order, but is not promising any delivery dates at the moment. Technically it should be possible to order them from any VW Van Dealers, because the part number appears on the configurator for both new vehicles, and in the parts departments, but it does appear that not all dealers are being that cooperative, and besides if you get it through SMG you'll get your 10% club discount!
 
So fitted the rack on Friday after upgrading the helicopter tape provided. The 3m Stuff from here was considerably thicker than the standard stickers (hope the link is ok) https://www.ebay.co.uk/itm/291957816366

Some pics of the rack fitted. I am impressed with it tbh and think I made the right choice
8aac1a586b91bcd5ec3d47892d3435b9.jpg
b45df4bdc3d8f38f61b9edc2546fe89a.jpg
 
Am I correct that the clamp on the frame doesn't lock with a key?
 
The clamps are lockable on the new rack, not sure about the old one.
 
Zooming in on the clamp, it looks like even if it was locked a hard yank upwards would release the bike.
 
20170409_152132.jpg We loaded 4 bikes on to our t6 yesterday for first time. Adds about a foot in height depending on your bike sizes plus a few inches width. Took about an hour to configure where each went! Took photos afterwards of each stage so 5 mins putting back on later. I like the chunkiness of the carrrier. The only pain (hence time to configure) is you can't put a child bike on the outside as the tyre holders are too far apart in that one (the bar is not one continuous one like the inner 3). And you have to use the short connector piece to hood your 3 and 4th bikes as the ones issued are only long enough for the first 3 slots. With a chunky frame bit worrying it might slip out so d locked it also.
 
Zooming in on the clamp, it looks like even if it was locked a hard yank upwards would release the bike.

I would never rely on any of the locking mechanisms on any of these bike racks - even the worst thief with the most basic tools would defeat them in seconds. Make sure if you have bikes you don't want to lose and you leave it out of site that you loop all the bikes and the rack together with a Sold Secure grade of preferably 12mm hardened chain and suitable padlock and cover them with a (preferably grotty looking) tarpaulin or similar.
 
Zooming in on the clamp, it looks like even if it was locked a hard yank upwards would release the bike.

The clamp jaws do grip well and curl quite a lot round the tube - certainly enough to hold the bike securely in transit. I'm not sure pulling it would release the bike but agree that it shouldn't be relied upon as a primary security mechanism.
 
I have the old "Kylie" bike rack.
Always put the heaviest bike on the rack first then the next heaviest etc. This is simple physics - creates less stress on the rack and the tailgate and also keeps as much of the load weight as near the vehicle wheels as possible. This means that the bikes will have the least effect on handling when driving as is possible.
Only one of the bikes can be "locked" with a key so this should always be on the last bike on the rack. You should not rely on this as being fully secure. You should add your own locks etc.
If your bike rack is held on by std Allen Screws consider replacing them with Resistorx screws as an extra deterrent against your whole rack being stolen (tip from susibus).
 
If your bike rack is held on by std Allen Screws consider replacing them with Resistorx screws as an extra deterrent against your whole rack being stolen (tip from susibus).

The new rack also uses these security screws throughout- should have mentioned that before!
 
The new rack also uses these security screws throughout- should have mentioned that before!
OK, good improvement for just a few ÂŁ's (Two screws plus hex driver is less than ÂŁ3 for a Kylie). Its one of those "why wouldn't you" make this small upgrades!
 
Oh, by the way - Resistorx Srcews are sometimes referred to as Pin Torx.
 
Can anybody provide these dimensions of the Quasi and Kylie racks when lowered - horizontal distance from tailgate to outer edge; vertical distance from outer edge to projection from top of bumper?

I'm trying figure out whether i can use either rack with my trailer. I'm fairly sure I can't but would like to check.

I only really need to carry 2 bikes so maybe the Fiamma Pro would work but people I've talked to aren't keen on Fiamma stuff.

My trailer won't carry bikes without some kind of mod.

Sent from my MotoE2(4G-LTE) using Tapatalk
 
I suspect I would be fine providing I only drive in a straight line
e55481ac9e04d51c6a50dc3488bd5eac.jpg


Sent from my MotoE2(4G-LTE) using Tapatalk
 
Thx JW, that's great.

Sent from my MotoE2(4G-LTE) using Tapatalk
 
Wouldn't it be nice if all life's questions were answered as quickly and concisely as they are on the Cali forum?

Well done Rik.

Oh by the way, are they 16", 17" or 18" wheels in the illustration?
 

Similar threads

SusiBus
Replies
86
Views
29K
Leepower11
L
M
Replies
0
Views
683
Mr Bean
M
C
Replies
0
Views
972
Cali197
C
Chris Hyde
Replies
1
Views
1K
markusschork
markusschork
Rupes
Replies
1
Views
1K
Rupes
Rupes
Back
Top