Protecting underside wiring from damage caused by foxes etc

Mine‘s in again with two sensors affected - adblue and exhaust … not looking cheap.. so clearly the heavy duty foil they used last time plus anti rodent tape didn’t do the trick. So annoying! Looking to do the gas pipe and cable tie solution this time
 
Mine‘s in again with two sensors affected - adblue and exhaust … not looking cheap.. so clearly the heavy duty foil they used last time plus anti rodent tape didn’t do the trick. So annoying! Looking to do the gas pipe and cable tie solution this time
Might be worth talking to these guys at Hilltop, we use them at work.

 
Might be worth talking to these guys at Hilltop, we use them at work.

Thanks v much - that looks like a great option. I’ve
sent them a message. I’ll keep you posted.
 
I ended enclosing the sensor wires in aluminium pipe, then attaching these anti climb/bird spikes to the piping with cable ties and chassis.
Also washed down the driveway with jeyes fluid as it smelled of foxes. Not had any issue since.

got the piping and spikes from Amazon.
If you have the option get a professional to do it.

E81C73BC-8F11-4D2F-8062-D4CF0A24CF8A.jpeg
 
Might be worth talking to these guys at Hilltop, we use them at work.

Thank you v much for this suggestion. I bought some of the metal woven braid wrap and also stainless tie wraps and now have them on the main cables. See the pic.

However, 2 days after getting the van back from replacing the sensor (££) I had an “oil sensor: workshop!” amber message come on! Today I’ve had the wheel alignment done at wheels in motion in Chesham (v good) and while they were at it they had a look and found yet another chewed cable to the oil sensor! Luckily they spliced a new cable in for me and it all seems ok for now but I’m guessing this can‘t be foxes and prob a mouse, rat or squirrel, since it was underneath the protective engine cover under the sump. V frustrating … it never seems to end.

E4081885-B9E3-45CD-811A-68A1B176AE88.jpeg

B95C3941-D9AD-4AC6-A904-1C49BF425E05.jpeg

AF7E0424-3E9D-4EEF-B11B-0231790968F6.jpeg

C2EBFE83-755E-40D8-8B02-005395106CD8.jpeg
 
Thank you v much for this suggestion. I bought some of the metal woven braid wrap and also stainless tie wraps and now have them on the main cables. See the pic.

However, 2 days after getting the van back from replacing the sensor (££) I had an “oil sensor: workshop!” amber message come on! Today I’ve had the wheel alignment done at wheels in motion in Chesham (v good) and while they were at it they had a look and found yet another chewed cable to the oil sensor! Luckily they spliced a new cable in for me and it all seems ok for now but I’m guessing this can‘t be foxes and prob a mouse, rat or squirrel, since it was underneath the protective engine cover under the sump. V frustrating … it never seems to end.

View attachment 81154

View attachment 81155

View attachment 81156

View attachment 81157
Good to hear, hopefully the protection will stop the majority of damage
 
Cars cover up as foxes drawn to tasty cables
One Worthing motorist puts his brake cables out of foxes’ reachOne Worthing motorist puts his brake cables out of foxes’ reach
ECO-FRIENDLY brake cables are being eaten by foxes, after manufacturers switched from petroleum-based insulation to soy, forcing owners to wrap their cars in tarpaulins.
Photographs show multiple cars covered in blue plastic for protection after a spate of attacks in Worthing, West Sussex, with locals claiming at least 20 vehicles were targeted by foxes.
Jack Cousens, the AA’s head of roads policy, said the animals may be attracted to the soy-based insulation on brake wires.
Since 2000, peanut and soy-based oils and waxes have been used on car parts including gearbox insulation, primer bulbs and diesel injector wires, instead of petroleum-based coverings.
“There are two reasons why foxes attack cars in this way,” Mr Cousens told The Telegraph. “The first is that some cables can be soy-based and therefore they get attracted to the taste of that.
“Secondly, within brake fluid there is something called glycol, which is a sweet-tasting alcoholic fluid, and they get a little bit attracted to that too. But they would only get attracted to it if they chew so far through the cable and uncover it.”
Eddie Mitchell, who lives in Worthing, the latest target for hungry foxes, said: “Everyone around us has been affected. There have been at least 20 attacks by foxes on the brakes system under cars.
“One neighbour ended up spending £1,500 on his Jaguar after it was attacked.”
Locals in Horsham, West Sussex, reported similar instances of foxes chewing through brake cables in 2021 and 2022 and residents in Sidcup, south-east London, were reportedly forced to fox-proof their cars last year.
The RAC said there were record numbers of mice, rats and foxes “surprising” its customers last year by causing serious damage.
 
Some time ago I started our van up and the engine management light came on. This turned out to be caused by an animal (fox or squirrel) chewing the wiring underneath the van.

More recently, another forum member (Mags21) has had a similar experience, except this time the problem recurred a week later.

I thought I'd have a look under the van and see if anything could be done to deter animals causing this expensive and inconvenient damage. This was my solution; if you decide to do the same you will need about half a metre of rubber gas pipe and a quantity of stout cable ties.

The wiring in question can be accessed by sliding underneath the van just aft of the nearside front wheel. To make access easier you can run the nearside front wheel up a ramp, taking adequate safety precautions while you are under the van. There are 4 wires as shown below.

View attachment 9276

Take the rubber gas pipe and slit it from one end to the other so it can be slipped over the wiring.

Next, cut it in to appropriate lengths to cover each of the wires and press it over, being careful not to disturb the plugs at the ends.

Finally, attach as many cables ties as you like over the pipe covered cables. Do not trim the ends of the ties right back, but cut then at an angle as shown below, so the ends are sharp. You can also attach ties to other vulnerable areas on the underside, rubber hoses, suction pipes etc. These sharply cut ties effectively mimic barbed wire and will make extremely unpleasant chewing for anything that fancies a bit of Cali wiring for dinner :D

View attachment 9277

Hope this is clear, it was a bit difficult taking photos under the van ....
Did this stop the problem? Had same issue twice in a few weeks £1600 of damage so desperately seeking solutions
 
I made a spiky deterrent. You can buy spiky mat/roll to keep cats off your garden. I attached some to a uPVC plank which I push under the van so it ends up under the area where the wiring looms are. 3 bricks make it challenging for Mr Fox to move. So far I have avoided a repeat repair. Also, Lidl sell a deterrent spray when they do motoring accessories. It's labelled Marten rather than Fox, but that's just a European regional variation!
 
If my experience last week has anything to go by, rub the cables with scotch bonnet peppers. You will need gloves to apply it. That will keep the vermin off them.
My partner once put a load of super hot chilli peppers in the hot press of an old cottage we were renting to dry out for something. They got eaten and so did the plastic container they came in by mice!
 
I keep on seeing a fox around where I park the Cali, I thought it would be prudent to make things a little harder to damage.

I started by moving the oil sensor cabling, it is clipped onto a specific bracket just behind the font anti roll bar slightly left of centre when looking forwards. The cable is held in position with a male saddle that clips onto a corresponding female fitting , simply slide the two apart to release the cable. Then re attach the cable higher up the bracket using the two exiting holes, this allows the cable that would otherwise hang down in fresh air to be tucked up behind the heat shield neatly (it is held to the heat shield with a factory saddle clamp.

IMG_5849.jpeg
 
Last edited:
Next I decide to look at the cables that could still be bitten relatively easily from under the van.
This thread started by showing gas hose used to wrap cables to add a level of protection.
I split some gas hose lengthways and applied it to several cables with Cable ties, I then cut the ties long at a slant to create a point. Images taken before cutting cable ties to a point

IMG_5853.jpeg


IMG_5851.jpeg
 
Last edited:
I then looked at the sensors on the Exhaust and the Add blue injector wiring.

The Adblue wiring was not wrapped , just cable tied to the injector coolant tubes to make it less accessible & more difficult to bite. (With a couple of cut cable ties to deter)

IMG_5854.jpeg

View attachment 152935

IMG_1425.jpeg
 
Last edited:
Does anyone have any experience/comments regarding the Vw Rodent Repellent kit that can be retrofitted to a van. Electrified wires, strobe and high frequency emitter???
 
The groundsman at my school playing field used to leave a diesel/oil soaked rag under the machines to prevent rodent damage.
 
I then looked at the sensors on the Exhaust and the Add blue injector wiring.

The Adblue wiring was not wrapped , just cable tied to the injector coolant tubes to make it less accessible & more difficult to bite. (With a couple of cut cable ties to deter)

View attachment 152930

View attachment 152935

View attachment 152942
I had the adblue wiring chewed twice on 3 months in London. It’s an easy way to spend £500 each time! I had the wire zip tied up and no issues in the last few years :thumb
 

Similar threads

Tapnstrum
Replies
34
Views
8K
Alan Baxter
A
G
Replies
0
Views
300
graemeplowman
G
L
Replies
2
Views
2K
Lesley54
L
G
Replies
9
Views
3K
Gavin ellis
G
Amarillo
Replies
47
Views
13K
Amarillo
Amarillo
Back
Top